UBNT airFiber AF5X/AF5U 5Ghz Point to Point Configuration.
UBNT airFiber AF5X/AF5U airFiber Login Device
airFiber AF5X/AF5U
is a firmware version and web interface of airFiber AF5X/AF5U radio.
Use your computer/Laptop LAN IP 192.168.1.10
or any other ( don’t use 192.168.1.20
in PC LAN
)
To login airFiber, AF5X/AF5U device use the default IP 192.168.1.20
UBNT airFiber AF5X/AF5U Login default username: ubnt
UBNT default login password: ubnt
Country
– choose your country from the list.
Language
– choose your country language
I agree to these Term OF USE
and the UBIQUITI FIRMWARE LICENSE AGREEMENT
– checkbox this option and press Login button
AirFiber AF5X/AF5U Master Mode Configuration :
For site, A AirFiber AF5X/AF5U
device will configure as AP mode. To configure in AirFiber AF5X/AF5U in AP mode follow the steps below.
Go to Settings gear on the right side top
Click on the Wireless tab.
Now follow the setting according to picture one by one.
1- Click on Setting
2- Click on Wireless
3- Wireless Mode: Master
4- Output Power: if you want to change the Output Power and/or Maximum Modulation Rate settings.
5-Link Name: Use Any name for your Point to Point Link Name.
6- Channel Width: use the 10/50 MHZ
according to area interference. If high interface recommended using 50Mhz
7-Maximum Modulation Rate: use the 1/4X-10X (1024QAM MIMO)
according to area interference.
8- Frequency Setting:
TX Frequency. This must match the RX Frequency on your other airFiber radio.
RX Frequency. This must match the TX Frequency of your other airFiber radio.
9- Wireless Security – set password for Point to Point link Security.
* After every one of the settings press Save Changes button to apply settings.
airFiber AF5 IP Address Configuration
airFiber configures with default IP 192.168.1.20
so every device must have a unique IP Address. In point to point radio, both location airFiber device should have different IP Address. You can Change IP Address from Network tab follow below instruction.
Click on Network tab
Management IP Address: choose Static or DHCP
- DHCP Fallback IP: Change IP Address here & Subnet mask
Click Change and Apply
AirFiber AF5X/AF5U Slave Mode Configuration :
Configure the Second gadget in Slave mode for point to point network.
Follow above Option to association and login second airFiber Radio to design as a slave.
After the login gadget pursues the arrangement offered beneath to build up a network with Master.
AirFiber AF5X/AF5U IP Address Configuration in the Slave Device
You must change the default IP Address in the salve device to avoid IP conflict with the Master device.
Follow the option given above airFiber AF5X/AF5U IP Address Configuration
airFiber AF5X/AF5U Slave Radio Wireless configure.
1- Click on Setting
2- Click on Wireless
3- Wireless Mode: Slave
( Choose Second Device Mode Slave)
4-Output Power: if you want to change the Output Power and/or Maximum Modulation Rate settings.
Link Name: Use the Same name used in Master Device.
5- Channel Width: use the 10/50 MHZ
according to area interference. If high interface recommended using 50Mhz
6-Maximum Modulation Rate: use the 1/4X-10X (1024QAM MIMO)
according to area interference.
7- Frequency Setting:
TX Frequency. This must match the RX Frequency on your other airFiber radio.
RX Frequency. This must match the TX Frequency of your other airFiber radio.
Configure the Wireless Security: use password set in Master Device
Click Change And Apply Settings
airFiber AF5X/AF5U IP Address Configuration Slave
Click on Network tab
Management IP Address: choose Static
or DHCP
- DHCP Fallback IP: Change IP Address here & Subnet mask
Click Change and Apply
airFiber AF5X/AF5U Point to Point Connectivity Status.
After complete Master and Slave configuration, you can see the Link Quality, CCQ and Throughput Status in the Main page of AirFiber AF5X and AF5U
airFiber AF5X/AF5U Firmware Upgrade Direct from Internet
Inside the system tab, you can manage your airFiber AF5 device. See the step below.
1: airFiber AF5X/AF5U Firmware Version – AF06.v4.0.3
2: airFiber AF5X/AF5U Firmware Upgrade- you can upgrade airFiber AF5X/AF5U directly from the internet and by uploading firmware file.
To direct up gradation from UBNT server configure the LAN with internet IP gateway and press check for update button inside system option.
3: Device Model – airFiber AF5X/AF5U ( see your airFiber AF5X/AF5U device model number )
Device name – airFiber AF5X/AF5U
Interface Language- change the airFiber AF5X/AF5U configuration settings language with your country language from this option.
4: External Reset button – enable airFiber AF5X/AF5U reset button from the software. If External reset button will off you cannot to factory reset airFiber AF5X/AF5U device from reset button on the device.
5: Date set- change the date and time zone of the device with this option.
6: System Account-Administrator username
7: Change Password
After doing al the setting doesn’t forget to save change settings to apply.
This is the basic user manual for airFiber AF5/5U Point to Point configuration for Long Distance.