Mikrotik Setting Point to Multi Point Using RB411AH

Posted on by

Good afternoon on this article I will discuss setting point to multipoint before my friends already know the difference between point to point with the point to multipoint, let me repeat again point to point means one point to point opponent while pointing to multipoint ie one point to many points that can be connected.

PTMP inspection

point to multipoint understanding by Wikipedia is communication made through different types from one to multiple connections, Point-to-multipoint is the most widely used in the wireless Internet (Wireless) and IP telephony through radio frequency. Point-to-Multipoint is also often abbreviated as P2MP, PTMP or PMP.

Devices Prepared

in this tutorial the tool I use as follows:
Gateway Router:

  • RB750

Routers as AccesPoint:

  • RB411AH complete with (Mini PCI: XR5, Pigtail, Jumper Panel, Large Horn, Box, Adapter 3A, Poe)
  • Cable Lan
  • Grid Antenna 24 dB

For Client as Station:

  • Groove complete with adapter and Poe
  • Little Horn

For Client2 as Station:

  • Groove complete with adapter and Poe
  • Little Horn

Topology

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

in the topology above there are two grooves that one gets the IP of the 750 router board and the other one from RB411AH I purposely use these two ways if there is a mistake please guide 🙂

There are 4 routers that we will configure the following steps

Routerboard 750 Configuration

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

 

The first step I do like the picture above, which makes rb750 can be connected to the internet

  1. enter the IP address (ether1: Internet, ether3: Local there are 2 IP)
  2. give IP / DNS
  3. give static routing
  4. check ping google.com
  5. give a firewall to access the Mikrotik station

Configure RB411AH

  • First, we set Bridge on Port wlan1 and ether1
Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point
Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

 

  • We Setting Wireless

Mode: AP Bridge
Frequency: (Specify)
SSID: (Specify)
Radio Name: (Specify)

 

on the WDS tab
WDS Mode: Dynamic
WDS Default Bridge: (Bridge made earlier)

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

Setting Ip address, DNS, and static routes

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

Groove configuration (IP of rb750)

Fill in Frequency, and scan list in rb411AH then click scan and Connect

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

replace mode with station wds, specify radio name

 

 

on WDS tap, WDS mode: Dynamic

We enter the IP we created in rb750, input DNS, and static route, and check ping google or etc

 

Groove configuration (IP of RB411AH)

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

Tap WDS: Dynamic
wds default bridge: none

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

We DHCP client, formerly DHCP server first on ether WLAN in rb411AH, After bound then check ping to internet

 

 

give IP address, according to the picture above, then give IP firewall nat to local IP is changed as if ip public who is surfing in google/internet, if not DHCP server, then give static IP on your computer/laptop

Mikrotik Setting Point to Multi Point
Mikrotik Setting Point to Multi-Point

 

 

views 635